In this sample chapter from Switching, Routing, and Wireless Essentials Companion Guide (CCNAv7) for Cisco Networking Academy students, you will learn how to troubleshoot common inter-VLAN configuration issues.
Objectives
Upon completion of this chapter, you will be able to answer the following questions:
What are the options for configuring inter-VLAN routing?
How do you configure router-on-a-stick inter-VLAN routing?
How do you configure inter-VLAN routing using Layer 3 switching?
How do you troubleshoot common inter-VLAN configuration issues?
Key Terms
This chapter uses the following key terms. You can find the definitions in the Glossary.
inter-VLAN routing Page 98
legacy inter-VLAN routing Page 98
router-on-a-stick Page 98
subinterfaces Page 100
switched virtual interface (SVI) Page 112
routed port Page 112
Introduction (4.0)
Now you know how to segment and organize your network into VLANs. Hosts can communicate with other hosts in the same VLAN, and you no longer have hosts sending out broadcast messages to every other device in your network, eating up needed bandwidth. But what if a host in one VLAN needs to communicate with a host in a different VLAN? If you are a network administrator, you know that people will want to communicate with other people outside of your network. This is where inter-VLAN routing can help you. Inter-VLAN routing uses a Layer 3 device, such as a router or a Layer 3 switch. Let’s take your VLAN expertise and combine it with your network layer skills and put them to the test!
Inter-VLAN Routing Operation (4.1)
In this section, you learn about two options for configuring for inter-VLAN routing.
What Is Inter-VLAN Routing? (4.1.1)
VLANs are used to segment switched Layer 2 networks for a variety of reasons. Regardless of the reason, hosts in one VLAN cannot communicate with hosts in another VLAN unless there is a router or a Layer 3 switch to provide routing services.
Inter-VLAN routing is the process of forwarding network traffic from one VLAN to another VLAN.
There are three inter-VLAN routing options:
Legacy Inter-VLAN routing: This is a legacy solution. It does not scale well.
Router-on-a-Stick: This is an acceptable solution for a small- to medium-sized network.
Layer 3 switch using switched virtual interfaces (SVIs): This is the most scalable solution for medium to large organizations.
Legacy Inter-VLAN Routing (4.1.2)
The first inter-VLAN routing solution relied on using a router with multiple Ethernet interfaces. Each router interface was connected to a switch port in different VLANs. The router interfaces served as the default gateways to the local hosts on the VLAN subnet.
For example, refer to the topology in Figure 4-1 where R1 has two interfaces connected to switch S1.
)
Figure 4-1 Legacy Inter-VLAN Routing Example
As shown in Table 4-1, the example MAC address table of S1 is populated as follows:
Fa0/1 port is assigned to VLAN 10 and is connected to the R1 G0/0/0 interface.
Fa0/11 port is assigned to VLAN 10 and is connected to PC1.
Fa0/12 port is assigned to VLAN 20 and is connected to the R1 G0/0/1 interface.
Fa0/11 port is assigned to VLAN 20 and is connected to PC2.
Table 4-1 MAC Address Table for S1
Port |
MAC Address |
VLAN |
F0/1 |
R1 G0/0/0 MAC |
10 |
F0/11 |
PC1 MAC |
10 |
F0/12 |
R1 G0/0/1 MAC |
20 |
F0/24 |
PC2 MAC |
20 |
When PC1 sends a packet to PC2 on another network, it forwards it to its default gateway 192.168.10.1. R1 receives the packet on its G0/0/0 interface and examines the destination address of the packet. R1 then routes the packet out its G0/0/1 interface to the F0/12 port in VLAN 20 on S1. Finally, S1 forwards the frame to PC2.
Legacy inter-VLAN routing using physical interfaces works, but it has a significant limitation. It is not reasonably scalable because routers have a limited number of physical interfaces. Requiring one physical router interface per VLAN quickly exhausts the physical interface capacity of a router.
In our example, R1 required two separate Ethernet interfaces to route between VLAN 10 and VLAN 20. What if there were six (or more) VLANs to interconnect? A separate interface would be required for each VLAN. Obviously, this solution is not scalable.
Router-on-a-Stick Inter-VLAN Routing (4.1.3)
The “router-on-a-stick” inter-VLAN routing method overcomes the limitation of the legacy inter-VLAN routing method. It requires only one physical Ethernet interface to route traffic between multiple VLANs on a network.
A Cisco IOS router Ethernet interface is configured as an 802.1Q trunk and connected to a trunk port on a Layer 2 switch. Specifically, the router interface is configured using subinterfaces to identify routable VLANs.
The configured subinterfaces are software-based virtual interfaces. Each is associated with a single physical Ethernet interface. Subinterfaces are configured in software on a router. Each subinterface is independently configured with an IP address and VLAN assignment. Subinterfaces are configured for different subnets that correspond to their VLAN assignment. This facilitates logical routing.
When VLAN-tagged traffic enters the router interface, it is forwarded to the VLAN subinterface. After a routing decision is made based on the destination IP network address, the router determines the exit interface for the traffic. If the exit interface is configured as an 802.1Q subinterface, the data frames are VLAN-tagged with the new VLAN and sent back out the physical interface.
Figure 4-2 shows an example of router-on-a-stick inter-VLAN routing. PC1 on VLAN 10 is communicating with PC3 on VLAN 30 through router R1 using a single, physical router interface.
)
Figure 4-2 Unicast from VLAN 10 Is Route to VLAN 30
Figure 4-2 illustrates the following steps:
Step 1. PC1 sends its unicast traffic to switch S2.
Step 2. Switch S2 tags the unicast traffic as originating on VLAN 10 and forwards the unicast traffic out its trunk link to switch S1.
Step 3. Switch S1 forwards the tagged traffic out the other trunk interface on port F0/3 to the interface on router R1.
Step 4. Router R1 accepts the tagged unicast traffic on VLAN 10 and routes it to VLAN 30 using its configured subinterfaces.
In Figure 4-3, R1 routes the traffic to the correct VLAN.
Figure 4-3 Router Tags Unicast Frame with VLAN 30
Figure 4-3 illustrates the following steps:
Step 5. The unicast traffic is tagged with VLAN 30 as it is sent out the router interface to switch S1.
Step 6. Switch S1 forwards the tagged unicast traffic out the other trunk link to switch S2.
Step 7. Switch S2 removes the VLAN tag of the unicast frame and forwards the frame out to PC3 on port F0/23.
)
Inter-VLAN Routing on a Layer 3 Switch (4.1.4)
The modern method of performing inter-VLAN routing is to use Layer 3 switches and switched virtual interfaces (SVI). An SVI is a virtual interface that is configured on a Layer 3 switch, as shown in Figure 4-4.
)
Figure 4-4 Layer 3 Switch Inter-VLAN Routing Example
Inter-VLAN SVIs are created the same way that the management VLAN interface is configured. The SVI is created for a VLAN that exists on the switch. Although virtual, the SVI performs the same functions for the VLAN as a router interface would. Specifically, it provides Layer 3 processing for packets that are sent to or from all switch ports associated with that VLAN.
The following are advantages of using Layer 3 switches for inter-VLAN routing:
They are much faster than router-on-a-stick because everything is hardware switched and routed.
There is no need for external links from the switch to the router for routing.
They are not limited to one link because Layer 2 EtherChannels can be used as trunk links between the switches to increase bandwidth.
Latency is much lower because data does not need to leave the switch to be routed to a different network.
They are more commonly deployed in a campus LAN than routers.
The only disadvantage is that Layer 3 switches are more expensive than Layer 2 switches, but they can be less expensive than a separate Layer 2 switch and router.
CHECK YOUR UNDERSTANDING—INTER-VLAN ROUTING OPERATION (4.1.5)
Refer to the online course to complete this activity.
Router-on-a-Stick Inter-VLAN Routing (4.2)
In this section, you configure router-on-a-stick inter-VLAN routing.
Router-on-a-Stick Scenario (4.2.1)
In the previous section, three ways to create inter-VLAN routing were listed, and legacy inter-VLAN routing was detailed. This section details how to configure router-on-a-stick inter-VLAN routing. You can see in the figure that the router is not in the center of the topology but instead appears to be on a stick near the border, hence the name.
In Figure 4-5, the R1 GigabitEthernet 0/0/1 interface is connected to the S1 FastEthernet 0/5 port. The S1 FastEthernet 0/1 port is connected to the S2 FastEthernet 0/1 port. These are trunk links that are required to forward traffic within and between VLANs.
)
Figure 4-5 Router-on-a-Stick Topology
To route between VLANs, the R1 GigabitEthernet 0/0/1 interface is logically divided into three subinterfaces, as shown in Table 4-2. The table also shows the three VLANs that will be configured on the switches.
Table 4-2 Router R1 Subinterfaces
Subinterface |
VLAN |
IP Address |
G0/0/1.10 |
10 |
192.168.10.1/24 |
G0/0/1.20 |
20 |
192.168.20.1/24 |
G0/0/1.30 |
99 |
192.168.99.1/24 |
Assume that R1, S1, and S2 have initial basic configurations. Currently, PC1 and PC2 cannot ping each other because they are on separate networks. Only S1 and S2 can ping each other, but they but are unreachable by PC1 or PC2 because they are also on different networks.
To enable devices to ping each other, the switches must be configured with VLANs and trunking, and the router must be configured for inter-VLAN routing.
S1 VLAN and Trunking Configuration (4.2.2)
Complete the following steps to configure S1 with VLANs and trunking:
Step 1. Create and name the VLANs. First, the VLANs are created and named, as shown in Example 4-1. VLANs are created only after you exit out of VLAN subconfiguration mode.
Example 4-1 Create and Name VLANs
S1(config)# vlan 10 S1(config-vlan)# name LAN10 S1(config-vlan)# exit S1(config)# vlan 20 S1(config-vlan)# name LAN20 S1(config-vlan)# exit S1(config)# vlan 99 S1(config-vlan)# name Management S1(config-vlan)# exit S1(config)#
Step 2. Create the management interface. Next, the management interface is created on VLAN 99 along with the default gateway of R1, as shown in Example 4-2.
Example 4-2 Create the Management Interface
S1(config)# interface vlan 99 S1(config-if)# ip add 192.168.99.2 255.255.255.0 S1(config-if)# no shut S1(config-if)# exit S1(config)# ip default-gateway 192.168.99.1 S1(config)#
Step 3. Configure access ports. Next, port Fa0/6 connecting to PC1 is configured as an access port in VLAN 10, as shown in Example 4-3. Assume PC1 has been configured with the correct IP address and default gateway.
Example 4-3 Configure Access Ports
S1(config)# interface fa0/6 S1(config-if)# switchport mode access S1(config-if)# switchport access vlan 10 S1(config-if)# no shut S1(config-if)# exit S1(config)#
Step 4. Configure trunking ports. Finally, ports Fa0/1 connecting to S2 and Fa05 connecting to R1 are configured as trunk ports, as shown in Example 4-4.
Example 4-4 Configure Trunking Ports
S1(config)# interface fa0/1 S1(config-if)# switchport mode trunk S1(config-if)# no shut S1(config-if)# exit S1(config)# interface fa0/5 S1(config-if)# switchport mode trunk S1(config-if)# no shut S1(config-if)# end *Mar 1 00:23:43.093: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up *Mar 1 00:23:44.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to up
S2 VLAN and Trunking Configuration (4.2.3)
The configuration for S2 is similar to S1, as shown in Example 4-5.
Example 4-5 S2 Configuration
S2(config)# vlan 10 S2(config-vlan)# name LAN10 S2(config-vlan)# exit S2(config)# vlan 20 S2(config-vlan)# name LAN20 S2(config-vlan)# exit S2(config)# vlan 99 S2(config-vlan)# name Management S2(config-vlan)# exit S2(config)# S2(config)# interface vlan 99 S2(config-if)# ip add 192.168.99.3 255.255.255.0 S2(config-if)# no shut S2(config-if)# exit S2(config)# ip default-gateway 192.168.99.1 S2(config)# interface fa0/18 S2(config-if)# switchport mode access S2(config-if)# switchport access vlan 20 S2(config-if)# no shut S2(config-if)# exit S2(config)# interface fa0/1 S2(config-if)# switchport mode trunk S2(config-if)# no shut S2(config-if)# exit S2(config-if)# end *Mar 1 00:23:52.137: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R1 Subinterface Configuration (4.2.4)
The router-on-a-stick method requires you to create a subinterface for each VLAN to be routed.
A subinterface is created using the interface interface_id.subinterface_id global configuration mode command. The subinterface syntax is the physical interface followed by a period and a subinterface number. Although not required, it is customary to match the subinterface number with the VLAN number.
Each subinterface is then configured with the following two commands:
encapsulation dot1q vlan_id [native]: This command configures the subinterface to respond to 802.1Q encapsulated traffic from the specified vlan-id. The native keyword option is only appended to set the native VLAN to something other than VLAN 1.
ip address ip-address subnet-mask: This command configures the IPv4 address of the subinterface. This address typically serves as the default gateway for the identified VLAN.
Repeat the process for each VLAN to be routed. Each router subinterface must be assigned an IP address on a unique subnet for routing to occur.
When all subinterfaces have been created, enable the physical interface using the no shutdown interface configuration command. If the physical interface is disabled, all subinterfaces are disabled.
In the configuration in Example 4-6, the R1 G0/0/1 subinterfaces are configured for VLANs 10, 20, and 99.
Example 4-6 R1 Subinterface Configuration
R1(config)# interface G0/0/1.10 R1(config-subif)# description Default Gateway for VLAN 10 R1(config-subif)# encapsulation dot1Q 10 R1(config-subif)# ip add 192.168.10.1 255.255.255.0 R1(config-subif)# exit R1(config)# R1(config)# interface G0/0/1.20 R1(config-subif)# description Default Gateway for VLAN 20 R1(config-subif)# encapsulation dot1Q 20 R1(config-subif)# ip add 192.168.20.1 255.255.255.0 R1(config-subif)# exit R1(config)# R1(config)# interface G0/0/1.99 R1(config-subif)# description Default Gateway for VLAN 99 R1(config-subif)# encapsulation dot1Q 99 R1(config-subif)# ip add 192.168.99.1 255.255.255.0 R1(config-subif)# exit R1(config)# R1(config)# interface G0/0/1 R1(config-if)# description Trunk link to S1 R1(config-if)# no shut R1(config-if)# end R1# *Sep 15 19:08:47.015: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to down *Sep 15 19:08:50.071: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to up *Sep 15 19:08:51.071: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/1, changed state to up R1#
Verify Connectivity Between PC1 and PC2 (4.2.5)
The router-on-a-stick configuration is complete after the switch trunk and the router subinterfaces have been configured. The configuration can be verified from the hosts, router, and switch.
From a host, verify connectivity to a host in another VLAN using the ping command. It is a good idea to first verify the current host IP configuration using the ipconfig Windows host command, as shown in Example 4-7.
Example 4-7 Verify Windows Host Configuration
C:\Users\PC1> ipconfig Windows IP Configuration Ethernet adapter Ethernet0: Connection-specific DNS Suffix . : Link-local IPv6 Address : fe80::5c43:ee7c:2959:da68%6 IPv4 Address : 192.168.10.10 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 C:\Users\PC1>
The output confirms the IPv4 address and default gateway of PC1. Next, use ping to verify connectivity with PC2 and S1, as shown in Figure 4-5. The ping output successfully confirms that inter-VLAN routing is operating, as shown in Example 4-8.
Example 4-8 Verify Inter-VLAN Routing by Pinging from PC1
C:\Users\PC1> ping 192.168.20.10
Pinging 192.168.20.10 with 32 bytes of data:
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Ping statistics for 192.168.20.10:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss).
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Users\PC1>
C:\Users\PC1> ping 192.168.99.2
Pinging 192.168.99.2 with 32 bytes of data:
Request timed out.
Request timed out.
Reply from 192.168.99.2: bytes=32 time=2ms TTL=254
Reply from 192.168.99.2: bytes=32 time=1ms TTL=254 |
Ping statistics for 192.168.99.2:
Packets: Sent = 4, Received = 2, Lost = 2 (50% loss).
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 2ms, Average = 1ms
C:\Users\PC1>
Router-on-a-Stick Inter-VLAN Routing Verification (4.2.6)
In addition to using ping between devices, the following show commands can be used to verify and troubleshoot the router-on-a-stick configuration.
show ip route
show ip interface brief
show interfaces
show interfaces trunk
As shown in Example 4-9, verify that the subinterfaces are appearing in the routing table of R1 by using the show ip route command. Notice that there are three connected routes (C) and their respective exit interfaces for each routable VLAN. The output confirms that the correct subnets, VLANs, and subinterfaces are active.
Example 4-9 Verify Subinterfaces Are in Routing Table
R1# show ip route | begin Gateway
Gateway of last resort is not set
192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.10.0/24 is directly connected, GigabitEthernet0/0/1.10
L 192.168.10.1/32 is directly connected, GigabitEthernet0/0/1.10
192.168.20.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.20.0/24 is directly connected, GigabitEthernet0/0/1.20
L 192.168.20.1/32 is directly connected, GigabitEthernet0/0/1.20
192.168.99.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.99.0/24 is directly connected, GigabitEthernet0/0/1.99
L 192.168.99.1/32 is directly connected, GigabitEthernet0/0/1.99
R1#
Another useful router command is show ip interface brief, as shown in Example 4-10. The output confirms that the subinterfaces have the correct IPv4 address configured, and that they are operational.
Example 4-10 Verify Subinterface IP Addresses and Status
R1# show ip interface brief | include up GigabitEthernet0/0/1 unassigned YES unset up up Gi0/0/1.10 192.168.10.1 YES manual up up Gi0/0/1.20 192.168.20.1 YES manual up up Gi0/0/1.99 192.168.99.1 YES manual up up R1#
Subinterfaces can be verified using the show interfaces subinterface-id command, as shown in Example 4-11.
Example 4-11 Verify Details of the Subinterface
R1# show interfaces g0/0/1.10
GigabitEthernet0/0/1.10 is up, line protocol is up
Hardware is ISR4221-2x1GE, address is 10b3.d605.0301 (bia 10b3.d605.0301)
Description: Default Gateway for VLAN 10
Internet address is 192.168.10.1/24
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 10.
ARP type: ARPA, ARP Timeout 04:00:00
Keepalive not supported
Last clearing of "show interface" counters never
R1#
The misconfiguration could also be on the trunking port of the switch. Therefore, it is also useful to verify the active trunk links on a Layer 2 switch by using the show interfaces trunk command, as shown in Example 4-12. The output confirms that the link to R1 is trunking for the required VLANs.
Example 4-12 Verify Trunk Link Status
S1# show interfaces trunk Port Mode Encapsulation Status Native vlan Fa0/1 on 802.1q trunking 1 Fa0/5 on 802.1q trunking 1 Port Vlans allowed on trunk Fa0/1 1-4094 Fa0/5 1-4094 Port Vlans allowed and active in management domain Fa0/1 1,10,20,99 Fa0/5 1,10,20,99 Port Vlans in spanning tree forwarding state and not pruned Fa0/1 1,10,20,99 Fa0/5 1,10,20,99 S1#
PACKET TRACER—CONFIGURE ROUTER-ON-A-STICK INTER-VLAN ROUTING (4.2.7)
In this Packet Tracer activity, you check for connectivity prior to implementing inter-VLAN routing. Then you configure VLANs and inter-VLAN routing. Finally, you enable trunking and verify connectivity between VLANs.
Inter-VLAN Routing using Layer 3 Switches (4.3)
In this section, you configure inter-VLAN routing using Layer 3 switches.
Layer 3 Switch Inter-VLAN Routing (4.3.1)
Modern enterprise networks rarely use router-on-a-stick because it does not scale easily to meet requirements. In these very large networks, network administrators use Layer 3 switches to configure inter-VLAN routing.
Inter-VLAN routing using the router-on-a-stick method is simple to implement for a small- to medium-sized organization. However, a large enterprise requires a faster, much more scalable method to provide inter-VLAN routing.
Enterprise campus LANs use Layer 3 switches to provide inter-VLAN routing. Layer 3 switches use hardware-based switching to achieve higher-packet processing rates than routers. Layer 3 switches are also commonly implemented in enterprise distribution layer wiring closets.
Capabilities of a Layer 3 switch include the ability to do the following:
Route from one VLAN to another using multiple switched virtual interfaces (SVIs).
Convert a Layer 2 switchport to a Layer 3 interface (that is, a routed port). A routed port is similar to a physical interface on a Cisco IOS router.
To provide inter-VLAN routing, Layer 3 switches use SVIs. SVIs are configured using the same interface vlan vlan-id command used to create the management SVI on a Layer 2 switch. A Layer 3 SVI must be created for each of the routable VLANs.
Layer 3 Switch Scenario (4.3.2)
In Figure 4-6, the Layer 3 switch, D1, is connected to two hosts on different VLANs. PC1 is in VLAN 10, and PC2 is in VLAN 20, as shown. The Layer 3 switch will provide inter-VLAN routing services to the two hosts.
)
Figure 4-6 Layer 3 Switch Inter-VLAN Routing Topology
Table 4-3 shows the IP addresses for each VLAN.
Table 4-3 D1 VLAN IP Addresses
VLAN Interface |
IP Address |
10 |
192.168.10.1/24 |
20 |
192.168.20.1/24 |
Layer 3 Switch Configuration (4.3.3)
Complete the following steps to configure S1 with VLANs and trunking:
Step 1. Create the VLANs. First, create the two VLANs as shown in Example 4-13.
Example 4-13 Create the VLANs
D1(config)# vlan 10 D1(config-vlan)# name LAN10 D1(config-vlan)# vlan 20 D1(config-vlan)# name LAN20 D1(config-vlan)# exit D1(config)#
Step 2. Create the SVI VLAN interfaces. Configure the SVI for VLANs 10 and 20, as shown in Example 4-14. The IP addresses that are configured will serve as the default gateways to the hosts in the respective VLANs. Notice the informational messages showing the line protocol on both SVIs changed to up.
Example 4-14 Create the SVI VLAN Interfaces
D1(config)# interface vlan 10 D1(config-if)# description Default Gateway SVI for 192.168.10.0/24 D1(config-if)# ip add 192.168.10.1 255.255.255.0 D1(config-if)# no shut D1(config-if)# exit D1(config)# D1(config)# int vlan 20 D1(config-if)# description Default Gateway SVI for 192.168.20.0/24 D1(config-if)# ip add 192.168.20.1 255.255.255.0 D1(config-if)# no shut D1(config-if)# exit D1(config)# *Sep 17 13:52:16.053: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up *Sep 17 13:52:16.160: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up
Step 3. Configure access ports. Next, configure the access ports connecting to the hosts and assign them to their respective VLANs, as shown in Example 4-15.
Example 4-15 Configure Access Ports
D1(config)# interface GigabitEthernet1/0/6 D1(config-if)# description Access port to PC1 D1(config-if)# switchport mode access D1(config-if)# switchport access vlan 10 D1(config-if)# exit D1(config)# D1(config)# interface GigabitEthernet1/0/18 D1(config-if)# description Access port to PC2 D1(config-if)# switchport mode access D1(config-if)# switchport access vlan 20 D1(config-if)# exit
Step 4. Enable IP routing. Finally, enable IPv4 routing with the ip routing global configuration command to allow traffic to be exchanged between VLANs 10 and 20, as shown in Example 4-16. This command must be configured to enable inter-VAN routing on a Layer 3 switch for IPv4.
Example 4-16 Enable IP Routing
D1(config)# ip routing D1(config)#
Layer 3 Switch Inter-VLAN Routing Verification (4.3.4)
Inter-VLAN routing using a Layer 3 switch is simpler to configure than the router-on-a-stick method. After the configuration is complete, the configuration can be verified by testing connectivity between the hosts.
From a host, verify connectivity to a host in another VLAN using the ping command. It is a good idea to first verify the current host IP configuration using the ipconfig Windows host command. The output in Example 4-17 confirms the IPv4 address and default gateway of PC1.
Example 4-17 Verify Windows Host Configuration
C:\Users\PC1> ipconfig Windows IP Configuration Ethernet adapter Ethernet0: Connection-specific DNS Suffix . : Link-local IPv6 Address : fe80::5c43:ee7c:2959:da68%6 IPv4 Address : 192.168.10.10 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 C:\Users\PC1>
Next, verify connectivity with PC2 using the ping Windows host command, as shown in Example 4-18. The ping output successfully confirms that inter-VLAN routing is operating.
Example 4-18 Verify Inter-VLAN Routing by Pinging from PC1
C:\Users\PC1> ping 192.168.20.10
Pinging 192.168.20.10 with 32 bytes of data:
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Reply from 192.168.20.10: bytes=32 time<1ms TTL=127
Ping statistics for 192.168.20.10:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Users\PC1>
Routing on a Layer 3 Switch (4.3.5)
If VLANs are to be reachable by other Layer 3 devices, they must be advertised using static or dynamic routing. To enable routing on a Layer 3 switch, a routed port must be configured.
A routed port is created on a Layer 3 switch by disabling the switchport feature on a Layer 2 port that is connected to another Layer 3 device. Specifically, configuring the no switchport interface configuration command on a Layer 2 port converts it into a Layer 3 interface. Then the interface can be configured with an IPv4 configuration to connect to a router or another Layer 3 switch.
Routing Scenario on a Layer 3 Switch (4.3.6)
In Figure 4-7, the previously configured D1 Layer 3 switch is now connected to R1. R1 and D1 are both in an Open Shortest Path First (OSPF) routing protocol domain. Assume inter-VLAN has been successfully implemented on D1. The G0/0/1 interface of R1 has also been configured and enabled. Additionally, R1 is using OSPF to advertise its two networks, 10.10.10.0/24 and 10.20.20.0/24.
)
Figure 4-7 Routing Scenario on a Layer 3 Switch Topology
Routing Configuration on a Layer 3 Switch (4.3.7)
Complete the following steps to configure D1 to route with R1:
Step 1. Configure the routed port. Configure G1/0/1 to be a routed port, assign it an IPv4 address, and enable it, as shown in Example 4-19.
Example 4-19 Configure the Routed Port
D1(config)# interface GigabitEthernet1/0/1 D1(config-if)# description routed Port Link to R1 D1(config-if)# no switchport D1(config-if)# ip address 10.10.10.2 255.255.255.0 D1(config-if)# no shut D1(config-if)# exit D1(config)#
Step 2. Enable routing, as shown in Example 4-20. Ensure IPv4 routing is enabled with the ip routing global configuration command.
Example 4-20 Enable Routing
D1(config)# ip routing D1(config)#
Step 3. Configure routing. Configure the OSPF routing protocol to advertise the VLAN 10 and VLAN 20 networks, along with the network that is connected to R1, as shown in Example 4-21. Notice the message informing you that an adjacency has been established with R1.
Example 4-21 Configure Routing
D1(config)# router ospf 10 D1(config-router)# network 192.168.10.0 0.0.0.255 area 0 D1(config-router)# network 192.168.20.0 0.0.0.255 area 0 D1(config-router)# network 10.10.10.0 0.0.0.3 area 0 D1(config-router)# ^Z D1# *Sep 17 13:52:51.163: %OSPF-5-ADJCHG: Process 10, Nbr 10.20.20.1 on GigabitEthernet1/0/1 from LOADING to FULL, Loading Done D1#
Step 4. Verify routing. Verify the routing table on D1, as shown in Example 4-22. Notice that D1 now has a route to the 10.20.20.0/24 network.
Example 4-22 Verify Routing
D1# show ip route | begin Gateway Gateway of last resort is not set 10.0.0.0/8 is variably subnetted, 3 subnets, 3 masks C 10.10.10.0/30 is directly connected, GigabitEthernet1/0/1 L 10.10.10.2/32 is directly connected, GigabitEthernet1/0/1 O 10.20.20.0/24 [110/2] via 10.10.10.1, 00:00:06, GigabitEthernet1/0/1 192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.10.0/24 is directly connected, Vlan10 L 192.168.10.1/32 is directly connected, Vlan10 192.168.20.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.20.0/24 is directly connected, Vlan20 L 192.168.20.1/32 is directly connected, Vlan20 D1#Step 5. Verify connectivity. At this time, PC1 and PC2 are able to ping the server connected to R1, as shown in Example 4-23.
Example 4-23 Verify Connectivity
C:\Users\PC1> ping 10.20.20.254 Pinging 10.20.20.254 with 32 bytes of data: Request timed out. Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Ping statistics for 10.20.20.254: Packets: Sent = 4, Received = 3, Lost = 1 (25% loss). Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Users\PC1> !================================================== C:\Users\PC2> ping 10.20.20.254 Pinging 10.20.20.254 with 32 bytes of data: Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Reply from 10.20.20.254: bytes=32 time<1ms TTL=127 Ping statistics for 10.20.20.254: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss). Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Users\PC2>
PACKET TRACER—CONFIGURE LAYER 3 SWITCHING AND INTER-VLAN ROUTING (4.3.8)
In this Packet Tracer activity, you configure Layer 3 switching and Inter-VLAN routing on a Cisco 3560 switch.
Troubleshoot Inter-VLAN Routing (4.4)
In this section, you learn how to troubleshoot issues in an inter-VLAN routing environment.
Common Inter-VLAN Issues (4.4.1)
By now, you know that when you configure and verify, you must also be able to troubleshoot. This section discusses some common network problems associated with inter-VLAN routing.
There are a number of reasons why an inter-VAN configuration may not work. All are related to connectivity issues. First, check the physical layer to resolve any issues where a cable might be connected to the wrong port. If the connections are correct, use the list in Table 4-4 for other common reasons why inter-VLAN connectivity may fail.
Table 4-4 Common Inter-VLAN Issues
Issue Type |
How to Fix |
How to Verify |
Missing VLANs |
|
show vlan [brief] show interfaces switchport ping |
Switch Trunk Port Issues |
|
show interfaces trunk show running-config |
Switch Access Port Issues |
|
show interfaces switchport show running-config interface ipconfig |
Router Configuration Issues |
|
show ip interface brief show interfaces |
Troubleshoot Inter-VLAN Routing Scenario (4.4.2)
Next, examples of some of these inter-VLAN routing problems are covered in more detail.
The topology in Figure 4-8 will be used for all of these issues.
)
Figure 4-8 Inter-VLAN Routing Troubleshooting Topology
The VLAN and IPv4 addressing information for R1 is shown in Table 4-5.
Table 4-5 Router R1 Subinterfaces
Subinterface |
VLAN |
IP Address |
G0/0/0.10 |
10 |
192.168.10.1/24 |
G0/0/0.20 |
20 |
192.168.20.1/24 |
G0/0/0.30 |
99 |
192.168.99.1/24 |
Missing VLANs (4.4.3)
An inter-VLAN connectivity issue could be caused by a missing VLAN. The VLAN could be missing if it was not created, it was accidently deleted, or it is not allowed on the trunk link.
For example, PC1 is currently connected to VLAN 10, as shown in the show vlan brief command output in Example 4-24.
Example 4-24 Verify VLAN for PC1
S1# show vlan brief
VLAN Name Status Ports
---- ------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
10 LAN10 active Fa0/6
20 LAN20 active
99 Management active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
S1#
Now assume that VLAN 10 is accidently deleted, as shown in Example 4-25.
Example 4-25 VLAN 10 Is Deleted
S1(config)# no vlan 10
S1(config)# do show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
20 LAN20 active
99 Management active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
S1(config)#
Notice that VLAN 10 is now missing from the output in Example 4-25. Also notice that port Fa0/6 has not been reassigned to the default VLAN. The reason is because when you delete a VLAN, any ports assigned to that VLAN become inactive. They remain associated with the VLAN (and thus inactive) until you assign them to a new VLAN or re-create the missing VLAN.
Use the show interface interface-id switchport command to verify the VLAN membership, as shown in Example 4-26.
Example 4-26 Verify an Interface’s VLAN Membership
S1(config)# do show interface fa0/6 switchport Name: Fa0/6 Switchport: Enabled Administrative Mode: static access Operational Mode: static access Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: native Negotiation of Trunking: Off Access Mode VLAN: 10 (Inactive) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none (Output omitted)
Re-creating the missing VLAN would automatically reassign the hosts to it, as shown in Example 4-27.
Example 4-27 Attempt to Re-create and Verify VLAN 10
S1(config)# vlan 10
S1(config-vlan)# do show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
20 LAN20 active
99 Management active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
S1(config-vlan)#
Notice that the VLAN has not been created as expected. The reason is because you must exit from VLAN sub-configuration mode to create the VLAN, as shown in Example 4-28.
Example 4-28 Exit VLAN Configuration Mode and Then Re-create and Verify VLAN
S1(config-vlan)# exit
S1(config)# vlan 10
S1(config)# do show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
10 VLAN0010 active Fa0/6
20 LAN20 active
99 Management active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
S1(config)#
Now notice that the VLAN is included in the list and that the host connected to Fa0/6 is on VLAN 10.
Switch Trunk Port Issues (4.4.4)
Another issue for inter-VLAN routing includes misconfigured switch ports. In a legacy inter-VLAN solution, this could be caused when the connecting router port is not assigned to the correct VLAN.
However, with a router-on-a-stick solution, the most common cause is a misconfigured trunk port.
For example, assume PC1 was able to connect to hosts in other VLANs until recently. A quick look at maintenance logs revealed that the S1 Layer 2 switch was recently accessed for routine maintenance. Therefore, you suspect the problem may be related to that switch.
On S1, verify that the port connecting to R1 (i.e., F0/5) is correctly configured as a trunk link using the show interfaces trunk command, as shown in Example 4-29.
Example 4-29 Verify Trunking
S1# show interfaces trunk Port Mode Encapsulation Status Native vlan Fa0/1 on 802.1q trunking 1 Port Vlans allowed on trunk Fa0/1 1-4094 Port Vlans allowed and active in management domain Fa0/1 1,10,20,99 Port Vlans in spanning tree forwarding state and not pruned Fa0/1 1,10,20,99 S1#
The Fa0/5 port connecting to R1 is mysteriously missing from the output. Verify the interface configuration using the show running-config interface fa0/5 command, as shown in Example 4-30.
Example 4-30 Verify Interface Configuration
S1# show running-config interface fa0/5 Building configuration... Current configuration : 96 bytes ! interface FastEthernet0/5 description Trunk link to R1 switchport mode trunk shutdown end S1#
As you can see, the port was accidently shut down. To correct the problem, reenable the port and verify the trunking status, as shown in Example 4-31.
Example 4-31 Reenable and Verify the Port
S1(config)# interface fa0/5 S1(config-if)# no shut S1(config-if)# *Mar 1 04:46:44.153: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to up S1(config-if)# *Mar 1 04:46:47.962: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to up S1(config-if)# do show interface trunk Port Mode Encapsulation Status Native vlan Fa0/1 on 802.1q trunking 1 Fa0/5 on 802.1q trunking 1 Port Vlans allowed on trunk Fa0/1 1-4094 Fa0/5 1-4094 Port Vlans allowed and active in management domain Fa0/1 1,10,20,99 Fa0/5 1,10,20,99 Port Vlans in spanning tree forwarding state and not pruned Fa0/1 1,10,20,99 Fa0/1 1,10,20,99 S1(config-if)#
To reduce the risk of a failed inter-switch link disrupting inter-VLAN routing, redundant links and alternate paths should be part of the network design.
Switch Access Port Issues (4.4.5)
When a problem is suspected with a switch access port configuration, use verification commands to examine the configuration and identify the problem.
Assume PC1 has the correct IPv4 address and default gateway but is not able to ping its own default gateway. PC1 is supposed to be connected to a VLAN 10 port.
Verify the port configuration on S1 using the show interfaces interface-id switchport command, as shown in Example 4-32.
Example 4-32 Verify the Port Configuration
S1# show interface fa0/6 switchport Name: Fa0/6 Switchport: Enabled Administrative Mode: static access Operational Mode: static access Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: native Negotiation of Trunking: Off Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none
The Fa0/6 port has been configured as an access port, as indicated by “static access”. However, it appears that it has not been configured to be in VLAN 10. Verify the configuration of the interface, as shown in Example 4-33.
Example 4-33 Verify the Port Configuration in the Running-Config
S1# show running-config interface fa0/6 Building configuration... Current configuration : 87 bytes ! interface FastEthernet0/6 description PC-A access port switchport mode access end S1#
Assign port Fa0/6 to VLAN 10 and verify the port assignment, as shown in Example 4-34.
Example 4-34 Assign the VLAN to the Port and Verify the Configuration
S1# configure terminal S1(config)# interface fa0/6 S1(config-if)# switchport access vlan 10 S1(config-if)# S1(config-if)# do show interface fa0/6 switchport Name: Fa0/6 Switchport: Enabled Administrative Mode: static access Operational Mode: static access Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: native Negotiation of Trunking: Off Access Mode VLAN: 10 (VLAN0010) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none (Output omitted)
PC1 is now able to communicate with hosts on other VLANs.
Router Configuration Issues (4.4.6)
Router-on-a-stick configuration problems are usually related to subinterface misconfigurations. For instance, an incorrect IP address was configured or the wrong VLAN ID was assigned to the subinterface.
For example, R1 should be providing inter-VLAN routing for users in VLANs 10, 20, and 99. However, users in VLAN 10 cannot reach any other VLAN.
You verified the switch trunk link and all appears to be in order. Verify the subinterface status using the show ip interface brief command, as shown in Example 4-35.
Example 4-35 Verify the Status of the Subinterfaces
R1# show ip interface brief Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0/0 unassigned YES unset administratively down down GigabitEthernet0/0/1 unassigned YES unset up up Gi0/0/1.10 192.168.10.1 YES manual up up Gi0/0/1.20 192.168.20.1 YES manual up up Gi0/0/1.99 192.168.99.1 YES manual up up Serial0/1/0 unassigned YES unset administratively down down Serial0/1/1 unassigned YES unset administratively down down R1#
The subinterfaces have been assigned the correct IPv4 addresses, and they are operational.
Verify which VLANs each of the subinterfaces is on. To do so, the show interfaces command is useful, but it generates a great deal of additional unrequired output. The command output can be reduced using IOS command filters as shown in Example 4-36.
Example 4-36 Verify the VLANs Configured on Each Subinterface
R1# show interfaces | include Gig|802.1Q GigabitEthernet0/0/0 is administratively down, line protocol is down GigabitEthernet0/0/1 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set GigabitEthernet0/0/1.10 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 100. GigabitEthernet0/0/1.20 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 20. GigabitEthernet0/0/1.99 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 99. R1#
The pipe symbol ( | ) along with some select keywords is a useful method to help filter command output. In this example, the keyword include was used to identify that only lines containing the letters “Gig” or “802.1Q” will be displayed. Because of the way the show interface output is naturally listed, using these filters produces a condensed list of interfaces and their assigned VLANs.
Notice that the G0/0/1.10 interface has been incorrectly assigned to VLAN 100 instead of VLAN 10. This is confirmed by looking at the configuration of the R1 GigabitEthernet 0/0/1.10 subinterface, as shown in Example 4-37.
Example 4-37 Verify the Configuration of the Subinterface in the Running-Config
R1# show running-config interface g0/0/1.10 Building configuration... Current configuration : 146 bytes ! interface GigabitEthernet0/0/1.10 description Default Gateway for VLAN 10 encapsulation dot1Q 100 ip address 192.168.10.1 255.255.255.0 end R1#
To correct this problem, configure subinterface G0/0/1.10 to be on the correct VLAN using the encapsulation dot1q 10 subinterface configuration mode command, as shown in Example 4-38.
Example 4-38 Correct and Verify the Subinterface Configuration
R1# conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# interface gigabitEthernet 0/0/1.10 R1(config-subif)# encapsulation dot1Q 10 R1(config-subif)# end R1# R1# show interfaces | include Gig|802.1Q GigabitEthernet0/0/0 is administratively down, line protocol is down GigabitEthernet0/0/1 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set GigabitEthernet0/0/1.10 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 10. GigabitEthernet0/0/1.20 is up, line protocol is up Encapsulation 802.1Q Virtual LAN, Vlan ID 20. GigabitEthernet0/0/1.99 is up, line protocol is up R1#
When the subinterface has been assigned to the correct VLAN, it is accessible by devices on that VLAN, and the router can perform inter-VLAN routing.
With verification, router configuration problems are quickly addressed, allowing inter-VLAN routing to function properly.
CHECK YOUR UNDERSTANDING—TROUBLESHOOT INTER-VLAN ROUTING (4.4.7)
Refer to the online course to complete this activity.
LAB—TROUBLESHOOT INTER-VLAN ROUTING (4.4.9)
In this lab, you complete the following objectives:
Part 1: Build the Network and Load Device Configurations
Part 2: Troubleshoot the Inter-VLAN Routing Configuration
Part 3: Verify VLAN Configuration, Port Assignment, and Trunking
Part 4: Test Layer 3 Connectivity
Summary (4.5)
The following is a summary of each section in the chapter:
Inter-VLAN Routing Operation
Hosts in one VLAN cannot communicate with hosts in another VLAN unless there is a router or a Layer 3 switch to provide routing services. Inter-VLAN routing is the process of forwarding network traffic from one VLAN to another VLAN. Three options include legacy, router-on-a-stick, and a Layer 3 switch using SVIs. Legacy used a router with multiple Ethernet interfaces. Each router interface was connected to a switch port in different VLANs. Requiring one physical router interface per VLAN quickly exhausts the physical interface capacity of a router. The router-on-a-stick inter-VLAN routing method requires only one physical Ethernet interface to route traffic between multiple VLANs on a network. A Cisco IOS router Ethernet interface is configured as an 802.1Q trunk and connected to a trunk port on a Layer 2 switch. The router interface is configured using subinterfaces to identify routable VLANs. The configured subinterfaces are software-based virtual interfaces associated with a single physical Ethernet interface. The modern method is Inter-VLAN routing on a Layer 3 switch using SVIs. The SVI is created for a VLAN that exists on the switch. The SVI performs the same functions for the VLAN as a router interface. It provides Layer 3 processing for packets being sent to or from all switch ports associated with that VLAN.
Router-on-a-Stick Inter-VLAN Routing
To configure a switch with VLANs and trunking, complete the following steps: create and name the VLANs, create the management interface, configure access ports, and configure trunking ports. The router-on-a-stick method requires a subinterface to be created for each VLAN to be routed. A subinterface is created using the interface interface_id.subinterface_id global configuration mode command. Each router subinterface must be assigned an IP address on a unique subnet for routing to occur. When all subinterfaces have been created, the physical interface must be enabled using the no shutdown interface configuration command. From a host, verify connectivity to a host in another VLAN using the ping command. Use ping to verify connectivity with the host and the switch. To verify and troubleshoot, use the show ip route, show ip interface brief, show interfaces, and show interfaces trunk commands.
Inter-VLAN Routing Using Layer 3 Switches
Enterprise campus LANs use Layer 3 switches to provide inter-VLAN routing. Layer 3 switches use hardware-based switching to achieve higher-packet processing rates than routers. Capabilities of a Layer 3 switch include routing from one VLAN to another using multiple switched virtual interfaces (SVIs) and converting a Layer 2 switch port to a Layer 3 interface (that is, a routed port). To provide inter-VLAN routing, Layer 3 switches use SVIs. SVIs are configured using the same interface vlan vlan-id command used to create the management SVI on a Layer 2 switch. A Layer 3 SVI must be created for each of the routable VLANs. To configure a switch with VLANS and trunking, complete the following steps: create the VLANS, create the SVI VLAN interfaces, configure access ports, and enable IP routing. From a host, verify connectivity to a host in another VLAN using the ping command. Next, verify connectivity with the host using the ping Windows host command. VLANs must be advertised using static or dynamic routing. To enable routing on a Layer 3 switch, a routed port must be configured. A routed port is created on a Layer 3 switch by disabling the switch port feature on a Layer 2 port that is connected to another Layer 3 device. The interface can be configured with an IPv4 configuration to connect to a router or another Layer 3 switch. To configure a Layer 3 switch to route with a router, follow these steps: configure the routed port, enable routing, configure routing, verify routing, and verify connectivity.
Troubleshoot Inter-VLAN Routing
There are a number of reasons why an inter-VAN configuration may not work. All are related to connectivity issues such as missing VLANs, switch trunk port issues, switch access port issues, and router configuration issues. A VLAN could be missing if it was not created, it was accidently deleted, or it is not allowed on the trunk link. Another issue for inter-VLAN routing includes misconfigured switch ports. In a legacy inter-VLAN solution, a misconfigured switch port could be caused when the connecting router port is not assigned to the correct VLAN. With a router-on-a-stick solution, the most common cause is a misconfigured trunk port. When a problem is suspected with a switch access port configuration, use ping and show interfaces interface-id switchport commands to identify the problem. Router configuration problems with router-on-a-stick configurations are usually related to subinterface misconfigurations. Verify the subinterface status using the show ip interface brief command.
PACKET TRACER—INTER-VLAN ROUTING CHALLENGE (4.5.1)
In this activity, you demonstrate and reinforce your ability to implement inter-VLAN routing, including configuring IP addresses, VLANs, trunking, and subinterfaces.
LAB—IMPLEMENT INTER-VLAN ROUTING (4.5.2)
In this lab, you complete the following objectives:
Part 1: Build the Network and Configure Basic Device Settings
Part 2: Create VLANs and Assign Switch Ports
Part 3: Configure an 802.1Q Trunk between the Switches
Part 4: Configure Inter-VLAN Routing on the S1 Switch
Part 5: Verify Inter-VLAN Routing is Working
Practice
The following activities provide practice with the topics introduced in this chapter. The Labs are available in the companion Switching, Routing, and Wireless Essentials Labs and Study Guide (CCNAv7) (ISBN 9780136634386). The Packet Tracer Activity instructions are also in the Labs & Study Guide. The PKA files are found in the online course.
LABS
Lab 4.2.8: Configure Router-on-a-Stick Inter-VLAN Routing
Lab 4.4.9: Troubleshoot Inter-VLAN Routing
Lab 4.5.2: Implement Inter-VLAN Routing
PACKET TRACER ACTIVITIES
Packet Tracer 4.2.7: Configure Router-on-a-Stick Inter-VLAN Routing
Packet Tracer 4.3.8: Configure Layer 3 Switching and Inter-VLAN Routing
Packet Tracer 4.4.8: Troubleshoot Inter-VLAN Routing
Packet Tracer 4.5.1: Inter-VLAN Routing Challenge
Check Your Understanding Questions
Complete all the review questions listed here to test your understanding of the sections and concepts in this chapter. The appendix “Answers to the ‘Check Your Understanding’ Questions” lists the answers.
1. A router has two FastEthernet interfaces and needs to connect to four VLANs in the local network. How can this be accomplished using the fewest number of physical interfaces without unnecessarily decreasing network performance?
Add a second router to handle the inter-VLAN traffic.
Implement a router-on-a-stick configuration.
Interconnect the VLANs via the two additional FastEthernet interfaces.
Use a hub to connect the four VLANS with a FastEthernet interface on the router.
2. What distinguishes traditional legacy inter-VLAN routing from router-on-a-stick?
Traditional routing is able to use only a single switch interface, whereas a router-on-a-stick can use multiple switch interfaces.
Traditional routing requires a routing protocol, whereas a router-on-a-stick only needs to route directly connected networks.
Traditional routing uses one port per logical network, whereas a router-on-a-stick uses subinterfaces to connect multiple logical networks to a single router port.
Traditional routing uses multiple paths to the router and therefore requires STP, whereas router-on-a-stick does not provide multiple connections and therefore eliminates the need for STP.
3. Subinterface G0/1.10 on R1 must be configured as the default gateway for the VLAN 10 192.168.10.0/24 network. Which command should be configured on the subinterface to enable inter-VLAN routing for VLAN 10?
encapsulation dot1q 10
encapsulation vlan 10
switchport mode access
switchport mode trunk
4. What is important to consider while configuring the subinterfaces of a router when implementing inter-VLAN routing?
The IP address of each subinterface must be the default gateway address for each VLAN subnet.
The no shutdown command must be given on each subinterface.
The physical interface must have an IP address configured.
The subinterface numbers must match the VLAN ID number.
5. What are the steps that must be completed in order to enable inter-VLAN routing using router-on-a-stick?
Configure the physical interfaces on the router and enable a routing protocol.
Create the VLANs on the router and define the port membership assignments on the switch.
Create the VLANs on the switch to include port membership assignment and enable a routing protocol on the router.
Create the VLANs on the switch to include port membership assignment and configure subinterfaces on the router matching the VLANs.
6. What two statements are true regarding the use of subinterfaces for inter-VLAN routing? (Choose two.)
Fewer router Ethernet ports required than in traditional inter-VLAN routing
Less complex physical connection than in traditional inter-VLAN routing
More switch ports required than in traditional inter-VLAN routing
Simpler Layer 3 troubleshooting than with traditional inter-VLAN routing
Subinterfaces have no contention for bandwidth
7. Which router-on-a-stick command and prompt on R1 correctly encapsulates 802.1Q traffic for VLAN 20?
R1(config-if)# encapsulation 802.1q 20
R1(config-if)# encapsulation dot1q 20
R1(config-subif)# encapsulation 802.1q 20
R1(config-subif)# encapsulation dot1q 20
8. What are two disadvantages of using the router-on-a-stick inter-VLAN routing method in a large network? (Choose two.)
A dedicated router is required.
It does not scale well.
It requires multiple physical interfaces on a router.
It requires subinterfaces to be configured on the same subnets.
Multiple SVIs are needed.
9. What is a characteristic of a routed port on a Layer 3 switch? (Choose two.)
It requires the switchport mode access interface config command.
It requires the no switchport interface config command.
It requires the switchport access vlan vlan-id interface config command.
It supports trunking.
10. What are two advantages of using a Layer 3 switch with SVIs for inter-VLAN routing? (Choose two.)
A router is not required.
It switches packets faster than using the router-on-a-stick method.
SVIs can be bundled into EtherChannels.
SVIs can be divided using subinterfaces.
SVIs eliminate the need for a default gateway in the hosts.